lunes, 30 de enero de 2012

ATUALIZACIONES

MaXfly5000+
mf5000_rel110

Dongle IKS MaXfly
mf_iks1000_rel110

Loader Dongle e MaXfly5000+
Loader Dongle PCtools


martes, 10 de enero de 2012

Atualizacao ra IKS DONGLE

NOTA ORIGINAL DA TEAM MAXLFY
<< The procedure to upload sw by the pc tool >>

Caution !! This upgrade will erase your key for IKS, so please make sure to save your key
           before performing the upgrade by this procedure.

1. connect your pc to the dongle or receiver using rs232 cable.
2. unzip the attached file "mf5000+_pc_tool.zip" and consequently the directory "mf5000+_pc_tool" will appear.
3. there, double-click "upgrade.exe".
4. in the window displayed, check "Port:working com1, Bits Rate:115200, Parity:Even" and then click "Connect".
   (Here, if you are upgrading the dongle, please turn the dongle off and then on.)
5. it is ok if the window is displaying the list showing "All Chunk, .....".
6. if the list is not be displayed and the message "Target not connect or target is error status" is displayed),
   (Here, if you are upgrading the receiver, please turn the receiver off and then on.), go to 3 and repeat.
7. double-click "All Chunk" to upload the .abs file, "maincode" to upload the .bin file
   and then select/enter the .abs or .bin file.
8. click "Next" and then wait till the uploading will be done.

<< Note1 ! >>
if the front panel(VFD) of mf5000+ will display "ASH" during performing "upgrade by usb" in main menu,
please upload the .abs file by the above procedure.

<< Note2 ! >>
please use this tool to upgrade both the dongle and receiver

----------------------------------------------------------------------------------------------------------


NOTA TRADUCIDA
<<O procedimento para fazer o upload sw pela ferramenta pc>>

Cuidado! Esta actualização irá eliminar a sua chave para IKS, então por favor não se esqueça de salvar sua chave
            antes de realizar a atualização por este procedimento.

1. ligar o pc para o dongle ou receptor utilizando o cabo rs232.
2. descompacte o arquivo anexado "mf5000 + _pc_tool.zip" e, conseqüentemente, o diretório "mf5000 _pc_tool +" irá aparecer.
3. lá, dê um duplo clique em "upgrade.exe".
4. na janela exibida, marque "Port: trabalhar com1, Taxa de Bits: 115200, Paridade: Even" e clique em "Connect".
    (Aqui, se você estiver atualizando o dongle, deve ligar o dongle e ligar novamente.)
5. é ok se a janela está exibindo a lista que mostra "All Chunk, .....".
6. se a lista não é ser exibido ea mensagem "Target não ligue nem é alvo de status de erro" é exibido),
    (Aqui, se você está atualizando o receptor, por favor desligar o receptor e daí em diante.), Vá até três e repita.
7. duplo clique em "Chunk" para se fazer o upload do arquivo. abs, "maincode" para carregar o arquivo. bin
    e selecione / entrar no abs. ou. bin arquivo.
8. clique em "Next" e aguarde até que o upload vai ser feito.

<<Nota1! >>
se o painel frontal (VFD) de mf5000 + exibirá "ASH" durante a realização de "upgrade por USB" no menu principal,
por favor, fazer o upload do arquivo. abs pelo processo acima descrito.

<<Note2! >>
por favor, use esta ferramenta para atualizar tanto o dongle e receptor


Atualizacao Dongle MaXfly http://www.4shared.com/file/FhCos5te/mf_iks1000_rel110.html




lunes, 9 de enero de 2012

MaXfly SETUP

This describes how to use IKS for maxfly

   ----------------------------------------------------------------
   < How to connect >
   internet ---- dongle ---- rs232 cable ---- maxfly

   ----------------------------------------------------------------
   < How to setup the dongle >
   1. connect the dongle to PC using rs232 cable
   2. unzip MfDongle1.1.zip and click MfDongle1.1.exe
   3. select "Port" to be used and click "Connect"
   4. how to setup the dongle is as follows:
      first, disable the firewall on the following 4 ports : 3901/3902/3903/3999
      and follow the below a) or b) depending on your current network setup.
      a) DHCP
         - select DHCP
         - click "Set Address" to apply this network setup to the dongle.
      b) Static
         - de-select DHCP
         - click "Get Address" to retrieve the current network setup of dongle
         - click "Clear" to clear it
         - fill out the IP Address, Subnet mask, Gateway and DNS for
           the new network setup of dongle.
           and then click "Set Address" to apply this new setup to the dongle
      c) If the dongle is not working,
         - click "Reset" to reboot the dongle 
         - try a) or b) again

   -----------------------------------------------------------------
   < How to setup the maxfly(mf1000+/2000+) >
   1. turn-on the dongle and receiver.
   2. press "8282" during watching video and consequently 
      the menu of title "Key Edit Menu" will appear
   3. in the menu, use "LEFT/RIGHT" to select "I-Slave"
      at the 3rd item from the bottom in the leftmost column
      and then press "OK" at "I-Slave"(IKS On) / "None"(IKS Off)
   4. Press "OK" at "Login", in the keyboard shown
      enter the key and then press "OK" at "Save"

   ------------------------------------------------------------------
   < How to setup the maxfly(mf3000+) >
   1. turn-on the dongle and receiver.
   2. press MENU and go to "Tools" and "Netwrok Setting"
   3. use "LEFT/RIGT" to make "Connection" On(IKS On) / Off(IKS Off)
   4. Press "OK" at "Network Key", in the keyboard shown
      enter the key and then press "OK" at "OK"

   ------------------------------------------------------------------
   < How to setup the maxfly(mf5000+) >
   1. disable the firewall on the following 4 ports : 3901/3902/3903/3999
   2. MENU -> Ferramentas -> Configurando a rede
      - Set Connection to Ligado
      - Enter the user's key at the network key
      - go to IP Setting and setup the user's lan to connect to the server.
        (refer to http://mundodigitalreceiver.blogspot.com/)

viernes, 6 de enero de 2012

Atualizacao MaXfly5000+ HDMI v.110

NOVA ATUALIZACAO versao 110 para receptor FTA MAXFLY 5000+ HDMI
Correcao Servidor IKS Para Manter a Lista de Canais atualizem com o .bin

mf5000_rel110.bin
http://www.4shared.com/file/oMoFOSq6/mf5000_rel110.html


mf5000_rel10.abs
http://www.4shared.com/file/qhTo7NmV/mf5000_rel110.html